MST
Packaging

Empty IC packages for prototype assembly

An empty (pre-molded or air-cavity) IC package lets you attach and wire-bond your own die without a full molding line. It is the usual route for MPW samples, sensor and MEMS prototypes, and engineering samples that must fit a standard socket or PCB footprint.

The packages listed on MST Store are available in plastic air-cavity QFN and HTCC ceramic formats.

Request a packaging quote

Plastic air-cavity vs ceramic

Package families available through MST
FamilyConstructionTypical use
Plastic air-cavity QFN (ALNP)LCP plastic body, copper lead frame, nickel-gold plating; JEDEC MO-220 outlines; sealed with a ceramic or plastic lid by adhesiveFast prototypes and engineering samples that do not need hermetic sealing
Ceramic QFN (CQFN / ALNC)HTCC multilayer ceramicPrototypes requiring a review of sealing and reliability requirements
CSOP small ceramic packagesHTCC ceramicSmall-outline ceramic prototypes
CSMD power packagesHTCC ceramicPower devices
Cavity BGA and CQFPCavity packageHigh pin-count prototypes (144 to 512 I/O)

The manufacturer states that its plastic air-cavity packages do not meet military-grade hermeticity. Ceramic material alone does not establish a hermetic assembly: confirm the package, lid, sealing process and required leak-test criteria.

Sizes listed on MST Store

Selected empty package part numbers
Part numberTypeBody size
ALNP-16-3-5Plastic air-cavity QFN163 × 3 mm
ALNP-24-4-5Plastic air-cavity QFN244 × 4 mm
ALNP-32-5-5Plastic air-cavity QFN325 × 5 mm
ALNP-48-7-5LCP QFN48, 0.5 mm pitch, 5.2 × 5.2 mm die-attach area, 0.65 mm cavity depth7 × 7 mm, 0.85 mm thick
ALNP-64-9-5HPlastic air-cavity QFN649 × 9 mm
ALNP-100-12-4HPlastic air-cavity QFN10012 × 12 mm
ALNC-48-7-5CHTCC ceramic QFN487 × 7 mm
CSOP-14HTCC CSOP ceramic16.80 × 15.50 mm
BGA1313-256BALLSCavity BGA, 256 balls13 × 13 mm
BGA2020-512BALLSCavity BGA, 512 balls20 × 20 mm

More than 40 sizes are listed in the catalogue. Request a quote.

How to choose

  • Die size plus bonding clearance must fit the cavity or die-attach area.
  • Pin count and pitch must match the test socket or PCB footprint you plan to use.
  • For hermetic requirements, ask for a compatible package/lid/sealing process and the required verification; do not approve from the ceramic material label alone.
  • Plan the lid: ceramic, metal or plastic lids are available for these packages.

Will the die, wire bonds and lid fit?

Use the internal package drawing, not just the outside dimensions
RequirementWhat to compareEvidence to request
Die placementDie length and width with tolerances against the usable die-attach areaCavity and die-attach drawing with assembly clearances
Vertical clearanceDie thickness, attach layer, wire-loop envelope and lid undersideAn assembled section with a common height datum and tolerances
Electrical connectionsRequired independent signals, power and ground against bond pads and external terminalsBond-pad map, routing/net map and proposed bond diagram
Lid and sealLid seating area, adhesive or seal geometry, opening and environmental requirementMatching lid drawing, sealing process and agreed inspection or leak test

Ball count is not a substitute for the connection map. Confirm which terminals are usable for your design and which are shared, reserved or unconnected.

Check the full height stack

A die can fit in plan view while its wire loops interfere with the lid. Compare the highest assembled feature with the lowest permitted lid underside using the same drawing datum. Include die-attach thickness, wire-loop variation, lid seating and package tolerances. If cavity depth and lid height use different datums, ask for a section before subtracting the numbers.

KYOCERA describes cavity structures with wire-bond shelves and lists different hermetic and non-hermetic sealing options. These are design choices to confirm for the selected package; they do not certify a catalogue candidate for your assembly.

What to send with a package RFQ

  • Die length, width and thickness; pad count, required I/O and a non-confidential bond-pad layout.
  • Preferred package type, body size and pitch.
  • Hermetic or non-hermetic requirement and lid type.
  • Quantity and whether you need empty bodies only, matched lids, die attach, wire bonding, sealing or test.
  • Known assembly limits, test temperature, target date and delivery country. Unknown details can be listed for follow-up.

Frequently asked questions

What is an empty IC package?

A finished package body with leads or balls and an open cavity, supplied without a die. You attach and wire-bond your own die, then seal it with a lid.

Are plastic air-cavity QFN packages hermetic?

The manufacturer states its plastic cavity packages do not meet military-grade hermeticity. If hermetic sealing is required, confirm a suitable package, lid and sealing process plus the specified leak test. Choosing HTCC ceramic alone is not confirmation.

Is a 256-ball package enough for 128 required I/O?

The ball count alone cannot answer that. Check the bond-pad and routing map for independent usable connections, power and ground assignments, shared nets and unconnected terminals, then review the proposed bond diagram.

Do the QFN packages follow a JEDEC outline?

The manufacturer lists its plastic air-cavity QFN packages as standardized to JEDEC MO-220.

Can I request assembly and test as well?

Yes. Use the packaging and test RFQ to describe die attach, wire bonding and test needs; MST reviews the scope and replies with options.

Package your prototype dies

Send a non-confidential die outline, thickness, required I/O, package preference and quantity. MST reviews the missing inputs and supplier options for a scoped quote.

Request a packaging quote

Related pages

Sources

Values are taken from the manufacturer documents above, checked 2026-11-03. Request a quote for current price and availability. MST is a distributor; products are made by the manufacturers named.