MST
Test sockets

QFN test sockets by pin count, body size and pitch

QFN contacts sit underneath the package; many devices also have a central exposed pad. A socket must match the device drawing, including body tolerances, contact layout and pitch. Pin count alone is not enough: a QFN48 can be 6 × 6 mm at 0.4 mm pitch or 7 × 7 mm at 0.5 mm pitch.

Use the table to shortlist a Plastronics QN-series socket. Before ordering, check the package drawing, test conditions and board interface with the socket manufacturer. A size match is a starting point for review.

Ask an engineer

QFN socket lookup

Plastronics (Smiths Interconnect) QN-series sockets available through MST
PackageBody sizePitchPart numberStore page
QFN163 × 3 mm0.5 mm16QN50S23030SKT-QFN16-3X3
QFN244 × 4 mm0.5 mm24QN50S14040SKT-QFN24-4X4
QFN325 × 5 mm0.5 mm32QN50S15050SKT-QFN32-5X5
QFN486 × 6 mm0.4 mm48QN40TS16060SKT-QFN48-6X6
QFN487 × 7 mm0.5 mm48QN50S17070SKT-QFN48-7X7
QFN649 × 9 mm0.5 mm64QN50S19090SKT-QFN64-9X9

Open the Store page for the exact body size and pitch. All six are listed as lidded clamshell sockets with BeCu contacts, Au over Ni (NiB optional); confirm the ordered configuration against the device and socket drawings.

QN-series range

  • Pitches: 0.40, 0.50, 0.65, 0.80 and 1.00 mm; for any other pitch, the pitch is confirmed against your package outline drawing (POD) at quotation.
  • Lidded and open-top sockets for packages up to 10 mm; lidded sockets for 10 mm to 16 mm.
  • Center ground pin standard on all sockets; optional copper heat slug for high-power devices.
  • Sockets for more than 80 JEDEC standard footprints.

Checks before you order

  • Match the body size and pitch from the device drawing, not just the pin count.
  • Check the exposed pad size against the socket ground contact.
  • Confirm whether you need a lidded or open-top socket for your loading method.
  • For burn-in, confirm the temperature rating and expected insertion life.

Same pin count, different package

Pin count does not identify a QFN. In the table above, QFN48 appears twice: 6 × 6 mm at 0.4 mm pitch (48QN40TS16060) and 7 × 7 mm at 0.5 mm pitch (48QN50S17070). A socket for one will not accept the other. Always order from the body size and pitch on the device package drawing.

Exposed pad and thermal path

  • Smiths Interconnect fits a center ground pin as standard on QN-series sockets, which contacts the exposed thermal pad.
  • For high-power devices an optional copper heat slug is offered; ask for it at quote stage if the device dissipates significant power during test.
  • Check that the exposed pad size on your drawing matches the socket ground contact.

Lidded or open-top for QFN

Smiths Interconnect offers QN-series sockets in lidded and open-top styles for packages up to 10 mm, and lidded only from 10 mm to 16 mm. The six sockets in the table are lidded clamshell sockets. If you need an open-top socket for frequent manual swaps or handler loading, confirm availability for your body size.

Will a thermal head reach the device?

The bottom exposed pad and the top surface contacted by a thermal head are different interfaces. An exposed-pad contact does not establish top-side access, and an open-top label does not establish clearance for your head.

Request a section drawing with the device loaded and the contacts compressed. Compare the head outline, contact face and approach path with the socket opening, package top height and surrounding hardware. Ironwood describes compression, heat removal and board support as parts of the socket assembly; its BGA example illustrates the review, not compatibility with a QFN device.

A fit checklist to send to the socket manufacturer

Compare the device, socket, thermal head and PCB together
CheckProvideAsk the manufacturer to confirm
Package and contactsDimensioned outline with tolerances, pin 1, contact pads and exposed padExact supported package drawing and contact map
Thermal-head accessHead outline, contact face and required test temperaturesOpening, keep-out area and loaded section drawing
Force and travelLoading method and device force limits, if knownRecommended force, working travel and mechanical stops for this assembly
Board interfacePCB thickness, pad pattern, mounting holes and underside componentsFootprint, orientation, mounting hardware and backing-plate clearance
Test conditionsCurrent, signal requirements, temperature range and expected insertionsRatings for the exact configuration, contact maintenance and replacement parts

Leave unknown inputs marked as unknown. Request the missing drawings or limits before approving a model; do not infer them from a product photograph.

Contact wear and contamination

Marvin Test Solutions explains that repeated insertions transfer small particles of the device lead plating (for example matte tin) onto the socket contacts, where they become resistive, and that hard device platings can wear the socket contact plating. Both raise contact resistance over time, so plan for contact cleaning and replacement in your test budget.

Frequently asked questions

Is there a QFN32 5x5 test socket?

Yes. The Plastronics 32QN50S15050 is a lidded QFN32 socket for a 5 × 5 mm body at 0.5 mm pitch, listed on MST Store as SKT-QFN32-5X5.

Which QFN48 socket do I need?

Start with the body and pitch: 48QN40TS16060 is listed for 6 × 6 mm at 0.4 mm pitch; 48QN50S17070 for 7 × 7 mm at 0.5 mm pitch. Confirm the full device drawing, contact map, loaded height, thermal access and PCB interface before selecting either.

Does an open-top QFN socket automatically work with my thermal head?

No. Compare the loaded socket section and top opening with the head contact face, approach path, force and travel. Ask the manufacturer to confirm the complete device/socket/head/board combination.

Do QFN sockets contact the exposed thermal pad?

Smiths Interconnect lists a center ground pin as standard on QN-series sockets, and an optional copper heat slug for high-wattage devices.

My QFN size is not in the table. Can you still source it?

Yes. Send the package drawing and MST will check the matching QN-series or open-top socket with the manufacturer.

Can I get an open-top QFN socket for a 12 mm package?

Smiths Interconnect lists open-top QN-series sockets for packages up to 10 mm; from 10 mm to 16 mm the series is lidded. Send the drawing and request a quote.

Ask an engineer

Start with a non-confidential package outline, test conditions and quantity. Mention thermal-head access or board constraints. MST reviews candidates and identifies what still needs manufacturer confirmation before quoting.

Ask an engineer

Related pages

Sources

Values are taken from the manufacturer documents above, checked 2026-11-13. Request a quote for current price and availability. MST is a distributor; products are made by the manufacturers named.