AS568 O-ring sizes and FKM vs FFKM selection
AS568 is the standard size list for inch O-rings. Each dash number fixes an inside diameter and a cross section, so “AS568-214” means the same size from every manufacturer; the material and hardness are specified separately.
For semiconductor equipment the material choice usually matters more than the size: FKM covers many general seals, while FFKM is used where heat, plasma or aggressive chemicals shorten FKM life.
AS568 dash-number series
| Dash series | Nominal CS | Actual CS | Tolerance |
|---|---|---|---|
| -004 to -050 | 1/16 in | 0.070 in (1.78 mm) | ±0.003 in |
| -102 to -178 | 3/32 in | 0.103 in (2.62 mm) | ±0.003 in |
| -201 to -284 | 1/8 in | 0.139 in (3.53 mm) | ±0.004 in |
| -309 to -395 | 3/16 in | 0.210 in (5.33 mm) | ±0.005 in |
| -425 to -475 | 1/4 in | 0.275 in (6.99 mm) | ±0.006 in |
Within a series the cross section stays the same and the inside diameter grows with the dash number.
How to pick the size
- Measure or read the groove: gland depth and groove width set the cross section; the groove diameter sets the inside diameter.
- If you have an old part number such as Parker 2-214, the last three digits are the AS568 dash number (AS568-214).
- Do not change cross section without changing the groove.
- Perfluoroelastomers may need more squeeze than FKM; Parker notes that groove recommendations may need adjusting for FFKM and for semiconductor applications.
FFKM plasma grades at a glance
| Kalrez grade | Hardness, Shore A | Maximum service temperature | Suggested processes |
|---|---|---|---|
| 9100 | 70 | 300 °C (572 °F) | HDPCVD, conductor (poly/metal) etch |
| 9300 | 77 | 300 °C (572 °F) | Conductor etch, dielectric (oxide) etch, ash/strip |
| 9500 | 76 | 310 °C (590 °F) | HDPCVD, SACVD/FCVD, PECVD curing |
| 9600 | 70 | 315 °C (599 °F) | PECVD/PEALD, SACVD/FCVD |
| 8002 | 69 | 275 °C (527 °F) | Ash/strip |
| 8705 | 77 | 327 °C (621 °F) | PECVD curing (quartz window seal) |
DuPont states these typical values are not for specification and that the useful temperature range may vary with seal design and application. FKM limits depend on the compound; use the FKM compound data sheet.
When FFKM is worth the cost
- Seal temperatures above the FKM limit.
- Exposure to plasma, ozone, or aggressive wet chemistry where FKM swells or erodes.
- Low outgassing or low particle requirements inside the process chamber.
- Where seal change-outs cost more in tool downtime than the seal itself.
What to send with an O-ring RFQ
- AS568 dash number (or ID and cross section) and quantity.
- Material: FKM with hardness, or FFKM with the compound or the process conditions.
- Process: temperature, chemistry or plasma gases, vacuum or pressure, static or dynamic.
- The OEM part number if you are replacing an equipment seal.
Full AS568 size list
This guide does not reproduce the AS568 size table. Use the AS568 size tables in the Parker O-Ring Handbook (ORD 5700, linked in the sources) for inside diameters and tolerances, or request a quote with the RFQ form on this page.
Squeeze, stretch and gland fill
Three numbers decide whether an O-ring will seal in a given groove. Squeeze is the cross section compressed by the gland: (CS − gland depth) ÷ CS. Stretch is how much the inside diameter is enlarged when the ring is fitted on a shaft or groove: (groove diameter − ring ID) ÷ ring ID. Gland fill is the O-ring cross-section area as a share of the groove area.
Worked example: a -2xx series ring has a 0.139 in cross section. In a gland 0.104 in deep, squeeze = (0.139 − 0.104) ÷ 0.139 = 25.2%.
Compare your results with the design charts for your seal type (static, dynamic, face or dovetail) in the Parker O-Ring Handbook. Parker notes that groove recommendations may need adjusting for perfluoroelastomers and for semiconductor applications.
O-ring squeeze, stretch and gland fill calculator
Enter dimensions in inches. Stretch needs the ring ID and the groove (or shaft) diameter it is fitted on.
- Squeeze: 25.2%
- Stretch: —
- Gland fill: 78.0%
Results are geometry only (nominal values, no tolerances, swell or stretch-related cross-section reduction). Compare them with the seal manufacturer design chart for your seal type and compound.
Frequently asked questions
How do I calculate O-ring squeeze?
Squeeze = (cross section − gland depth) ÷ cross section. For example, a 0.139 in cross section in a 0.104 in deep gland gives 25.2%. Use the calculator on this page and compare the result with the manufacturer design chart for your seal type.
What does an AS568 dash number tell me?
It fixes the O-ring inside diameter and cross section. For example, every size from -201 to -284 has a 0.139 in (3.53 mm) cross section. It does not specify material or hardness.
What is the temperature limit of FKM vs FFKM?
FKM limits depend on the compound, so use the FKM compound data sheet. For FFKM, the DuPont Kalrez plasma selector guide lists maximum service temperatures from 275 °C (8002) to 327 °C (8705), with 9100 and 9300 at 300 °C. DuPont notes the useful range varies with seal design and application.
Can I drop an FFKM O-ring into a groove designed for FKM?
Often yes for size, but Parker notes perfluoroelastomers may need more squeeze than FKM for best sealing.
Which AS568 sizes and materials does MST Store list?
MST Store lists AS568 sizes in FKM 75 Shore A and in FFKM, with the FFKM compound and hardness confirmed in the quotation. Other sizes and compounds can be sourced on request.
Ask an engineer
Send the dash numbers, material and process conditions. MST replies with price and lead time.
Ask an engineerRelated pages
Sources
Values are taken from the manufacturer documents above, checked 2026-10-23. Request a quote for current price and availability. MST is a distributor; products are made by the manufacturers named.