MST
RFQ cartCart

AS568-012 O-rings: FFKM vs FKM 75A, and which Morisz grade for which seal

Need a part from this thread? Let MST find it

This thread is attached to your request. Add the part, your email and quantity; no account needed.

Can't find this part? We'll source it

Send us the part number and quantity. An MST engineer will source it, check that it fits your application, and reply with a quote.

Short answer: AS568-012 is one size (ID 9.25 mm × CS 1.78 mm). The choice is the compound. FKM 75A covers general vacuum, gas and fluid seals up to about 205 °C. Plasma, aggressive chemistry or higher heat points to FFKM, and the MORISEAL Morisz grade then depends on where the seal sits.
OptionTemp. rangeHardnessColourListed use
FKM 75A (AS568-012-FKM75-RFQ)−26 to +205 °C (general range)75 Shore ANot statedGeneral vacuum, gas, fluid static seals
Morisz 5130UP−5 to 250 °C80±5 HAPearl whiteDynamic contact points in plasma
Morisz MPF506UP−5 to 250 °C80±5 HAWhiteSpecialty gas pipelines
Morisz 6002UP / 5802SP0 to 300 °C80±5 / 75±5 HAAmberHigh temp. with water vapour, O₂, O₃
Morisz 6880SP / 6880SZ0 to 315 °C80±5 HABrownPlasma under mechanical stress
Morisz N650 to 330 °C75±5 HABlackPlasma at high temperature
Morisz ST50i−45 to 200 °C65±5 HAIvoryLow temperature, plasma, corrosive media
AS568-012 size callout: inside diameter 9.25 mm and cross section 1.78 mm
Illustration by MST Engineering. Schematic dimensions from the AS568 size, not a photograph of a moulded part.

1. The size

  • ID 0.364 ± 0.005 in (9.25 ± 0.13 mm)
  • CS 0.070 ± 0.003 in (1.78 ± 0.08 mm)
  • OD 0.504 in (12.81 mm), reference only (ID + 2 × CS)
  • Some FFKM grades mould slightly off the AS568 nominal size because of shrinkage. If the fit is critical, ask for the moulded dimensions.

2. FFKM vs FKM at this size

  • FKM 75A: Parker ORD 5700 gives a general service range of −26 to +205 °C. Ketones, amines and low-molecular-weight esters are typical exclusions.
  • FFKM: use it for plasma or aggressive chemistry. The Morisz grades run from −45 °C (ST50i) to 330 °C (N65). Compression set at 200 °C / 70 h ranges from 9 % (6880SZ) to 24 % (ST50i).
  • Do not treat the two compounds as interchangeable. Check the media, peak temperature and vacuum or bake-out against your tool or process spec.
Chart of FKM 75A and Morisz FFKM grades matched to semiconductor seal locations
Illustration by MST Engineering. Use the chart with the listed temperature and media limits, not as a drop-in substitution guide.

3. Which one for which seal location

1. General vacuum port, gas or fluid seal, no plasma, below 205 °C: FKM 75A. 2. Moving contact point in plasma: Morisz 5130UP. 3. Specialty gas line fitting: Morisz MPF506UP. 4. Hot zone with water vapour, oxygen or ozone: Morisz 6002UP or 5802SP (5802SP is the softer grade, 75 HA). 5. Hot plasma with the seal under compression: Morisz 6880SP or 6880SZ (6880SZ has the lower compression set, 9 %). 6. Highest temperature: Morisz N65, up to 330 °C. Confirm how long it can run at the upper limit. 7. Cold service: Morisz ST50i, down to −45 °C.

4. Quote it

  • Request AS568-012-FFKM-RFQ and name the Morisz grade, or request AS568-012-FKM75-RFQ.
  • Include the groove drawing, process media, peak temperature, vacuum level and bake-out, quantity and cleanroom packaging.
  • MST is the distributor. The manufacturer, compound, hardness and lead time are confirmed in the quotation.
Related: AS568 size and material guide, FFKM vs FKM for semiconductor seals, and the Morisz grades thread (#4).

Original OEM documents (links only)

The size and FKM temperature range in this note follow SAE AS568 and Parker ORD 5700 as cited in the body. Store listings and the related guides are linked above as plain URLs.

Ask an engineer

Parts
Catalog parts in this guide

Replies (0)

No replies yet.

Can't find this part? We'll source it

Send us the part number and quantity. An MST engineer will source it, check that it fits your application, and reply with a quote.