MST
询价清单购物车
Test sockets

IC test socket selection guide

An IC test socket holds a packaged device against a test or burn-in board without soldering, so the same board can test many parts. Picking the right one comes down to the package footprint, the lead pitch, how the lid opens and what the socket will be used for: bench validation, programming, final test or burn-in.

This guide covers the choices buyers make most often and lists the socket models available through MST from Plastronics (Smiths Interconnect), Enplas and Elnec.

Ask an engineer

Start with the package, not the socket

  • Package family and pin count, for example QFN32, QFP64 or SOIC8.
  • Body size in millimetres and lead pitch (0.4 mm, 0.5 mm, 1.27 mm and so on).
  • Exposed pad: QFN sockets usually need a center ground contact for the thermal pad.
  • The JEDEC outline or the device datasheet drawing, so the socket maker can confirm the footprint.

Lid style: clamshell or open-top

A lidded (clamshell) socket closes a hinged lid over the device and is common for manual bench work and burn-in. An open-top socket is loaded from above by pressing the frame, which suits frequent manual swaps and automated handling. Smiths Interconnect offers both lidded and open-top QN-series sockets for QFN packages up to 10 mm, and lidded sockets for 10 mm to 16 mm packages.

Contact type and use case

  • QFN contacts: the Plastronics QN-series QFN sockets listed below use BeCu contacts, Au over Ni (Smiths Interconnect QN-Series datasheet, Materials).
  • Pinch or tweezer contacts in open-top QFP sockets, such as the Enplas OTQ series, grip the gull-wing leads.
  • ZIF programming adapters, such as the Elnec DIL8W/SOIC8, convert a surface-mount package to a DIL plug for device programmers.
  • Burn-in: for long burn-in runs, send the temperature range and cycle count with your quote request and MST checks the socket rating.

Test sockets available through MST

Socket models listed on MST Store (manufacturer part numbers)
PackageBodyPitchManufacturerPart numberStyle
QFN163 × 3 mm0.5 mmPlastronics (Smiths Interconnect)16QN50S23030Lidded clamshell, BeCu contacts
QFN244 × 4 mm0.5 mmPlastronics (Smiths Interconnect)24QN50S14040Lidded clamshell, BeCu contacts
QFN325 × 5 mm0.5 mmPlastronics (Smiths Interconnect)32QN50S15050Lidded clamshell, BeCu contacts
QFN486 × 6 mm0.4 mmPlastronics (Smiths Interconnect)48QN40TS16060Lidded clamshell, BeCu contacts
QFN487 × 7 mm0.5 mmPlastronics (Smiths Interconnect)48QN50S17070Lidded clamshell, BeCu contacts
QFN649 × 9 mm0.5 mmPlastronics (Smiths Interconnect)64QN50S19090Lidded clamshell, BeCu contacts
QFP64 (LQFP/TQFP)10 × 10 mm0.5 mmEnplasOTQ-64-0.5-01Open-top, pinch contact
SOIC8 150 mil3.9 mm1.27 mmElnec70-0901 (DIL8W/SOIC8 ZIF 150mil)ZIF programming adapter

The same pin count can come in several body sizes; send the drawing and request a quote.

What to send with a socket RFQ

  • Device package drawing or JEDEC outline, pin count, body size and pitch.
  • Use case: bench test, programming, final test or burn-in, and the temperature range.
  • Board interface: through-hole, surface-mount or an existing board footprint you must match.
  • Quantity and target date.

Troubleshooting falling yield

Symptoms that point to the socket rather than the device
SymptomLikely causeWhat to check
Yield falls slowly over many insertionsLead-plating particles building up on the contactsInspect and clean the contacts; compare with a fresh socket
Device needs more force to passContact plating worn by hard device platingReplace contacts or the socket; review the contact plating option
Intermittent fails that move between sitesWorn or contaminated contacts on one siteSwap the socket between sites and see if the fail follows it
Fails only on a new package lotPackage outline or plating changeCompare the drawing and plating with the previous lot

Contamination and wear mechanisms per Marvin Test Solutions KB Q200240. Socket life and cleaning intervals depend on the socket model; ask the manufacturer for the rated values.

Quick decision path

  • Programming a few devices on a bench: a ZIF programming adapter for the package (for example SOIC8 150 mil).
  • Bench validation of QFN devices: a lidded clamshell QFN socket with BeCu contacts, matched to body size and pitch.
  • Frequent manual swaps or handler loading: an open-top socket (QFP: pinch contact; QFN up to 10 mm: open-top QN series).
  • Burn-in: send the temperature range and cycle count with your quote request and MST checks the socket rating before ordering.
  • Package not listed: send the drawing; Smiths Interconnect lists QN-series sockets for more than 80 JEDEC footprints.

Frequently asked questions

What is the difference between a test socket and a burn-in socket?

Both hold a device without soldering. A burn-in socket is built for long runs at elevated temperature on a burn-in board, while a test socket is used for functional or parametric test and bench validation. Many lidded QFN sockets are offered for both uses; confirm the rated temperature and cycle life for your run.

Which pitches do Plastronics QN-series QFN sockets cover?

Smiths Interconnect lists the QN series in 0.40, 0.50, 0.65, 0.80 and 1.00 mm pitches, with a center ground pin as standard. For any other pitch, the pitch is confirmed against your package outline drawing (POD) at quotation.

Can I get a socket for a package that is not listed?

Yes. Smiths Interconnect states QN-series sockets exist for more than 80 JEDEC standard footprints. Send the package drawing and MST will check availability and lead time with the manufacturer.

Does MST manufacture test sockets?

No. MST is a distributor. Sockets are made by the manufacturers named on each product page, and MST sources and quotes them.

Why does contact resistance rise as a socket ages?

Marvin Test Solutions describes two mechanisms: particles of device lead plating are transferred and embedded on the socket contacts, and hard device platings wear the socket contact plating. Both increase resistance and can lead to intermittent contact.

Ask an engineer

Send the package drawing, pitch and use case. MST replies with price and lead time.

Ask an engineer

Related pages

Sources

Values are taken from the manufacturer documents above, checked 2026-10-23. Request a quote for current price and availability. MST is a distributor; products are made by the manufacturers named.